How Much Does a Grow Light Cost to Run? Calculate Your Electric Bill
To find what a grow light costs to run, multiply its real wattage by the hours it's on each day, divide by 1,000 to get kilowatt-hours, then multiply by the rate on your electric bill. This guide shows you where to find each number, walks through an example, and helps you add in fans and heaters.
This guide is for adults 21+ in places where growing at home is legal. Laws differ by state and city and can change, so check your state and local rules before you start.
The simple formula
Your utility bills you for energy in kilowatt-hours (kWh). The U.S. Energy Information Administration (EIA) explains that a kilowatt is 1,000 watts, and one kilowatt-hour is one kilowatt used for one hour. So all you need to do is turn your light's watts and hours into kWh, then multiply by your rate.
Watts × hours per day ÷ 1,000 = kWh per day
kWh per day × days = kWh for the period
kWh for the period × your rate per kWh = cost
That's it. You can do it on your phone's calculator in under a minute. The only tricky part is getting the right numbers to plug in, which is what the next two sections are about.
Step 1: Find your light's real watts
This is where most people go wrong. Grow light listings often put a large number in the product name that is not what the light actually pulls from the wall. Some say "equivalent" to an older, hotter type of light. Others just use a big number that sounds impressive.
What you want is the actual power draw, sometimes listed as "actual power," "input power" or "power consumption" on the spec sheet or the label on the light itself. That's the number your electric meter sees.
Three ways to find it
- Check the spec sheet or manual. Look for actual or input power in watts, not "equivalent" or "replaces."
- Check the label on the driver or fixture. It often lists input watts or volts and amps.
- Measure it. A plug-in power meter goes between the wall and the light's plug and shows the watts the light is actually drawing. This is the most reliable way, and it works for fans and other gear too.
If your light has a dimmer, the draw changes with the setting. Measure at the setting you actually use.
Some links below are affiliate links. If you buy through them we may earn a small commission at no extra cost to you.
Step 2: Find your electricity rate
Use the rate on your own electric bill. It's the number that matters, because rates vary a lot between states, utilities and plans.
- Look for a line showing the price per kWh. Some bills split this into "supply" or "generation" plus "delivery" or "distribution." For a rough estimate, add those per-kWh charges together.
- If your plan has different prices at different times of day, or tiers that change as you use more, note that. It affects when it's cheapest to run your lights.
- Fixed monthly charges don't change when you add a grow light, so leave them out of this math.
If you don't have a bill handy yet, the EIA publishes average electricity prices by state and by sector (including residential) in its Electric Power Monthly, Table 5.6.A. Treat that as a ballpark only. Your own bill is always the better number.
A worked example (example numbers only)
Here's the math with simple, made-up round numbers so you can see how it works. These are not typical prices or a typical light. Swap in your own light's real watts and your own rate.
Say your light draws 200 watts from the wall, it runs 18 hours a day, and your rate is $0.15 per kWh.
| Step | Math | Result |
|---|---|---|
| kWh per day | 200 × 18 ÷ 1,000 | 3.6 kWh |
| kWh per 30 days | 3.6 × 30 | 108 kWh |
| Cost per 30 days | 108 × $0.15 | $16.20 |
Now say the same light runs 12 hours a day instead:
| Step | Math | Result |
|---|---|---|
| kWh per day | 200 × 12 ÷ 1,000 | 2.4 kWh |
| kWh per 30 days | 2.4 × 30 | 72 kWh |
| Cost per 30 days | 72 × $0.15 | $10.80 |
Same light, same rate, and the shorter schedule costs a third less. Hours matter as much as watts.
Why veg and flower cost different amounts
The number of hours your light is on per day changes during the grow. A Tennessee State University Extension guide to indoor hemp growing describes a vegetative phase of at least 14 to 18 hours of light per day, and flowering triggered by 12 hours of light and 12 hours of dark.
So if you grow photoperiod plants, your light costs more per day in veg than in flower. To estimate the whole grow, work out each stage separately and add them together:
- Veg: watts × veg hours ÷ 1,000 × number of veg days × rate.
- Flower: watts × 12 ÷ 1,000 × number of flower days × rate.
- Add the two.
If you keep the same light schedule for the whole grow, one line of math is enough. Seed type affects this, so if you're still choosing, our post on autoflower vs photoperiod seeds covers the differences.
Use a timer so the light runs exactly the hours you planned. It's also the easiest way to make sure your estimate matches reality.
Don't forget fans, heaters and humidifiers
The light is usually the biggest single load, but it isn't the only one. Use the same formula for every device, then add them up.
- Exhaust fan: often runs around the clock, so use 24 hours. A small fan running all day can add up.
- Clip fans: usually small, but count them if they run all day.
- Space heater: can be a big draw when it's running. Heaters cycle on and off, so a plug-in meter that tracks kWh over a few days gives a better number than the label alone.
- Humidifier or dehumidifier: also cycles, so measure if you can.
Here's a fill-in table you can copy into a notebook or spreadsheet:
| Device | Real watts | Hours per day | kWh per day (W × h ÷ 1,000) |
|---|---|---|---|
| Grow light | ____ | ____ | ____ |
| Exhaust fan | ____ | 24 | ____ |
| Clip fan(s) | ____ | ____ | ____ |
| Heater / humidifier | measured | — | ____ |
| Total | ____ × days × your rate |
If you use a space heater, follow the U.S. Consumer Product Safety Commission's advice: plug it directly into a wall outlet, never into an extension cord or power strip, and keep it at least three feet from things that can burn. Our post on keeping a grow tent warm in winter covers cheaper and safer ways to hold heat first.
Ways to keep the bill down
- Buy on real watts, not marketing watts. Compare lights by actual power draw and by what the maker says about coverage.
- Size the light to the space. A light much bigger than your tent wastes power. You don't need a $2,000 setup for a first grow.
- Run lights during cheaper hours if your plan has time-of-day pricing. In winter, running them at night can also help keep the tent warm.
- Use a timer so lights never run longer than planned.
- Measure once, then estimate. A plug-in meter for a few days tells you more than any guess.
One more thing to check before you plug anything in: make sure growing is allowed where you live, under state rules and local city or county rules, and that your lease or HOA allows it.
Common beginner mistakes
- Using the big number in the product name. Use actual watts from the spec sheet or a meter.
- Forgetting the fan. An exhaust fan running 24 hours a day is part of the bill.
- Using a state average instead of your own rate. Averages are a ballpark, not your bill.
- Using one schedule for the whole photoperiod grow. Veg and flower hours differ, so do the math for each.
Frequently asked questions
How do I calculate how much my grow light costs to run?
Multiply the light's actual watts by the hours it runs per day, then divide by 1,000 to get kWh per day. Multiply by the number of days, then by the price per kWh on your electric bill.
What wattage should I use for an LED grow light?
Use the actual power draw listed on the spec sheet or the light's label, or measure it with a plug-in power meter. Don't use an "equivalent" wattage, which describes a different kind of light.
Where do I find my electricity rate?
Your electric bill shows the price per kWh, sometimes split into supply and delivery charges. Add the per-kWh charges together for a rough estimate. The EIA publishes state averages, but your own bill is more accurate.
Does flowering cost less than veg?
For photoperiod plants, usually yes, because the light runs fewer hours per day in flower. One extension guide describes 14 to 18 hours of light in veg and 12 hours in flower. If you keep one schedule for the whole grow, one calculation covers it.
Do I need to count the exhaust fan?
Yes. Exhaust fans often run 24 hours a day, so even a small one adds to the total. Use the same formula with 24 hours, or measure it with a plug-in meter.
Keep reading
Sources
- U.S. Energy Information Administration — Measuring electricity
- U.S. Energy Information Administration — Electric Power Monthly, Table 5.6.A: Average Price of Electricity to Ultimate Customers by End-Use Sector, by State
- Tennessee State University Cooperative Extension — Indoor Cultivation of Floral Hemp in Modified Rooms (Omondi, Davis and Kumar)
- U.S. Consumer Product Safety Commission — Keep Warm and Safe This Winter: Tips for Using Generators, Furnaces and Space Heaters
This article is for general information and education only. It is not legal advice. Growing laws vary by state and city and change often; confirm the rules where you live. For adults 21+ only.
BeginnersGrowGuide.com is a participant in the Amazon Services LLC Associates Program and may earn from qualifying purchases and other affiliate links, at no extra cost to you.